Glass bottle cutter: It's Not as Difficult as You Think


If your restaurant will be serving wine, you must take care to serve it properly. Wine served properly can enhance and optimize the taste and bouquet, while serving it improperly will cause your wine to taste differently, even badly.



Most wines have a proper serving temperature for optimal taste. Light colored wines, including white wines, rosés and most sparkling wines will taste their best if served chilled at about 45 to 50 degrees. This temperature can be obtained by refrigerating the wine for about 1 - 2 hours before serving. Red wines are usually best served at a slightly cool room temperature, typically 60 to 65 degrees. Remember that on a hot day, all wines should be served slightly cooler than usual.

Chilling Wine

Your restaurant should have a proper ice bucket which allows you to fill it about 3/4 full of ice with some water. Place the wine in the bucket for 30 minutes before serving. Having the wine properly chilled will let your customers taste the wine at its best.


The shape of the glass that wine is served in has an effect on the taste and bouquet of any wines you serve. Your restaurant should have the proper glassware for serving wines, this includes champagne glasses, flutes, rhines, port glasses, sherry glasses and all purpose wine glasses. White wine should be served in tulip shaped glasses. Red wine should be served in larger, rounded glasses with a nice size bowl. Sparkling wine and champagne should be served in tall and thin flute glasses.

Opening The Bottle

The server should use a high quality corkscrew to open the wine for the customer. There are several types of corkscrews, including the traditional, winged and screwpull. A restaurant should usually use a waiters corkscrew, made in stainless steel, it has a very sharp, serrated foil cutter with a thumb stud and a 5 turn steel spiral. Using the waiters corkscrew, remove the foil using the blade. Push the point of the corkscrew into the middle of the cork. Continue twisting the corkscrew until just one loop remains above the cork. Place the notch on top of the lever onto the lip of the wine bottle. Hold the tip of the lever against the bottle's lip, while using your other hand to stabilize the bottle, then slowly lift the lever to ease the cork out of the bottle about two thirds of the way. Grab the rest of the cork with your fingers and twist out. Use a napkin to wipe any wine from the bottle.

As with all things, there is essential equipment and then there is would be nice to have equipment.

Essential Equipment

Glass Cutter

Cutting glass is not difficult, but you do need a good glass cutter. There are various glass cutters to choose from. My personal favorite glass cutter is the pistol cutter. It is important to choose a cutter that works well for you, as this is a stained glass tool you will use constantly.

There are basically two types of cutters, one with steel wheels and those with tungsten carbide wheels.

Cutters with steel wheels tend to be less expensive but, usually don't last very long. The steel wheel becomes dull after repetitive use and must be replaced. Steel wheels are good for general purpose or softer glass. The size of the wheel and angle of the bevel on the wheel will determine how hard of a glass it can score.

Tungsten carbide wheels are more expensive than steel wheels. There durability tends to out weigh the cost difference. Many are self-lubricating which can save time.

Glass Grinders

Grinders are used to smooth out cuts and insure exact fitting, as well as to lessen the chance of cutting yourself. The alternative to a grinder is a diamond file. This is less expensive, but the time and effort needed far out weights buying a grinder.

When choosing a grinder consider the size of the work surface, the power of the grinder and the accessories included such as bits, face shield and foot switch.. Additional considerations should be the warranty and price

Soldering Iron

There are a wide variety of different manufactures, types and sizes of soldering irons. Most soldering irons range from 60 to 150 watts with tip sizes ranging from 1/8 inch to 3/8 inch. When choosing your iron check out how long it takes to heat up, how long it holds the correct temperature, does it have a temperature controller and are the tips removable.

Probably, the most important thing to consider when doing stained glass soldering, is to choose an iron that feels comfortable in your hand. If the iron is not comfortable, then this will more than likely show up in your solder lines.

Yes, price it a factor, but remember, a good quality soldering iron will last for years and give professional results.

Soldering Iron Stand

After choosing your soldering iron, you will need to purchase a soldering stand. The stand can be simple or elaborate. The simple ones hold your iron and sponge, whereas, the more expensive ones will have a built-in temperature controller, iron stand, sponge, power cord, a solder roll holder, flux bottle well, brush and a catch-all tray. Needless to say, the more elaborate ones will cost more.

Temperature Controller

If your iron does not include a built-in temperature controller, then you will definitely need a separate controller. Glass bottle cutter Using a temperature controller will maintain a constant temperature for your soldering iron.

Breaking Pliers and Grozer Pliers

These two hand tools are used for breaking glass. Breaking pliers are used after you score a line and want to break the glass. Grozer pliers are used for breaking away small areas of glass.

Semi-Optional Equipment

Foiler Burnisher

A foiler burnisher is used with Tiffany construction (copper foil). This tool will allow you to securely press and adhere the copper foil to the glass. A burnisher is an inexpensive tool though you could use a tongue depressor.

Table Foiler

A table foiler automatically peels off the paper backing, centers it to the edges of the glass and partially crimps it. Using a table foiler will also eliminate copper foil from unwinding and becoming tangled.

Came Saw

Came saws are used to cut metal came in either zinc, brass or copper. Came saws range from a manual model to a power mitre chop saw.

A manual came saw consist of a precision saw and a mitre vise. This is the least expensive of all came saws, but will require more time and effort. Electric power came saws range from 90 to 250 watt units. Blade sizes vary from 2 inches to 5 ¾ inches.

All came saws adjust from 0 to 45 degrees allowing for proper mitres.

The more powerful the came saw, the easier it will cut, not to mention durability.

Cork-Backed Stainless Steel Ruler

This is a steel ruler that is backed in cork. This is nice when drawing or cutting lines on glass. The cork backing eliminates the ruler from slipping.

Soft Bristle Scrub Brush

The soft bristle scrub brush is great for polishing your stained glass. With its soft bristles, it is able to get into the tiniest crevices.

A Fid

This inexpensive tool is used to widen came. This becomes very important when using heavily textured glass.

Optional Stained Glass Tools

Glass Saw

A glass saw is a nice addition to a stained glass workshop. With a glass saw you can make intricate cuts that otherwise would not be possible.

Glass saws can be a ring saw, band saw or wire saw. A ring saw has a circular diamond coated blade that allows you to cut in all directions. The band saw has a linear diamond coated blade and can cut glass up to ¾ of an inch thick. The wire saw has the thinnest blade giving you more flexibility for cutting intricate shapes and narrow cut lines.

All three types of saws come with various built-in features. It is up to you as to which one to choose. It needs to meet your own personal needs.

Came Bender

The came bender will perform precision curves on zinc, brass and copper came. This means greater design freedom when rigid came is used. With the came bender you can make circular and oval panels.

Copper Foil Sheers

These are specially designed sheers that will cut paper pattern pieces leaving the correct spacing needed for copper foil or lead.

Layout Blocks

These are used to hold cut pieces of glass together until you are ready to solder.

Glass Cutting Systems

There is a variety of glass cutting systems available. These systems will allow you to make repetitive and geometric shapes. Some of the more popular systems include Morton Portable Glass Shop, Circle and Strip Cutters, and Jitter Bug.

Light Box

The light box is nice for drawing patterns and viewing glass combinations.

Glass Drills

Glass drills are use to drill holes in glass.